Invoke-NSUnsetIPv6
SYNOPSIS
Clears one or more NetScaler ipv6 resource properties.
SYNTAX
Invoke-NSUnsetIPv6 [-TrafficDomain] <Int32> [-Dodad] [-Natprefix] [-Ndbasereachtime] [-Ndretransmissiontime]
[-RaLearning] [-RouterRedirectIon] [-USIPNatprefix] [-Session <PSObject>] [-IgnoreNotFound]
[-ReturnNullOnNotFound] [-ThrowOnWarning] [-PassThru] [-WhatIf] [-Confirm] [<CommonParameters>]
DESCRIPTION
Configuration for ip v6 resource.
EXAMPLES
EXAMPLE 1
EXAMPLE 2
PARAMETERS
-TrafficDomain
Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0. Default value: 0 Minimum value = 0 Maximum value = 4094
Type: Int32
Parameter Sets: (All)
Aliases:
Required: True
Position: 1
Default value: 0
Accept pipeline input: True (ByPropertyName)
Accept wildcard characters: False
-Dodad
Enable the Citrix ADC to do Duplicate Address Detection (DAD) for all the Citrix ADC owned IPv6 addresses regardless of whether they are obtained through stateless auto configuration, DHCPv6, or manual configuration. Default value: DISABLED Possible values = ENABLED, DISABLED
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-Natprefix
Prefix used for translating packets from private IPv6 servers to IPv4 packets. This prefix has a length of 96 bits (128-32 = 96). The IPv6 servers embed the destination IP address of the IPv4 servers or hosts in the last 32 bits of the destination IP address field of the IPv6 packets. The first 96 bits of the destination IP address field are set as the IPv6 NAT prefix. IPv6 packets addressed to this prefix have to be routed to the Citrix ADC to ensure that the IPv6-IPv4 translation is done by the appliance.
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-Ndbasereachtime
Base reachable time of the Neighbor Discovery (ND6) protocol. The time, in milliseconds, that the Citrix ADC assumes an adjacent device is reachable after receiving a reachability confirmation. Default value: 30000 Minimum value = 1
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-Ndretransmissiontime
Retransmission time of the Neighbor Discovery (ND6) protocol. The time, in milliseconds, between retransmitted Neighbor Solicitation (NS) messages, to an adjacent device. Default value: 1000 Minimum value = 1
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-RaLearning
Enable the Citrix ADC to learn about various routes from Router Advertisement (RA) and Router Solicitation (RS) messages sent by the routers. Default value: DISABLED Possible values = ENABLED, DISABLED
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-RouterRedirectIon
Enable the Citrix ADC to do Router Redirection. Default value: DISABLED Possible values = ENABLED, DISABLED
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-USIPNatprefix
IPV6 NATPREFIX used in NAT46 scenario when USIP is turned on.
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-Session
The NetScaler session. If omitted, the current default session is used.
Type: PSObject
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: (Get-NSSession)
Accept pipeline input: False
Accept wildcard characters: False
-IgnoreNotFound
Returns null instead of throwing for known NITRO not-found responses.
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-ReturnNullOnNotFound
Returns null instead of throwing for known NITRO not-found responses.
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-ThrowOnWarning
Treats NITRO warning responses as terminating errors.
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-PassThru
Returns the updated resource after the operation completes.
Type: SwitchParameter
Parameter Sets: (All)
Aliases:
Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False
-WhatIf
Shows what would happen if the cmdlet runs. The cmdlet is not run.
Type: SwitchParameter
Parameter Sets: (All)
Aliases: wi
Required: False
Position: Named
Default value: None
Accept pipeline input: False
Accept wildcard characters: False
-Confirm
Prompts you for confirmation before running the cmdlet.
Type: SwitchParameter
Parameter Sets: (All)
Aliases: cf
Required: False
Position: Named
Default value: None
Accept pipeline input: False
Accept wildcard characters: False
CommonParameters
This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutVariable, -OutBuffer, -PipelineVariable, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.
INPUTS
OUTPUTS
System.Management.Automation.PSCustomObject
NOTES
Generated from NetScaler NITRO API metadata. Generated: 2026-06-01 21:28 Supported metadata versions: 13.1, 14.1.